AI FutureFTC Team #31591

Think · BIOBUZZ 2026–27

Engineering Notebook

Every time we fix or design something on the robot, we write it up as an entry (EN). We have written 114 entries from September 24 to November 20. Here is each one in a sentence, grouped by part of the robot.

New here? Start with the season story (the big decisions) or the robot versions (how the robot changed).

Drivetrain 13 Intake, lane + transfer 27 Shooter, turret + head 35 Flower wedge 9 Electronics + code 7 Frame + build process 23

What each entry covers

  1. Problem: what we saw on the robot or in CAD.
  2. Analysis: what we measured and why it happened, with real numbers.
  3. Options: the ideas we compared, with pros and cons.
  4. Decision: what we picked and why.
  5. Build: the parts and files we made.
  6. Test: how it worked, and what's next.

We say plainly how far each one got: Built + tested Built, testing Files ready (cut and print files made, not made yet) CAD only Plan / study Not chosen. The tag shows which robot version it belongs to: Wood robot CR1 CR1 v6 v6 METAL. There is no EN-87.

For the full write-ups of our October work (with photos and bench test numbers), read the five October design stories.

13 entries

Drivetrain

Two chain-driven pods with mecanum wheels. How we made them strong, square and inside 18 inches.

  1. EN-06Sep 27 · Wood robotA motor plate for the goBILDA drive motors (replaced by EN-07).Replaced
  2. EN-07Sep 28 · Wood robotThe chain was a quarter link off, so we moved the motors 0.8 mm; we also fixed a short axle and bolts in the chain's path.Built, testing
  3. EN-22Oct 15 · Wood robotPrinted ties for the drive pods and one front-right test pod.Files ready
  4. EN-25Oct 16 · Wood robotA drivetrain-only frame and 4 drill guides for the cross ties.Files ready
  5. EN-40Oct 24 · Wood robotOur U-channel was 10 mm too short, so we drew a plywood rear cross panel.Files ready
  6. EN-61Nov 2 · Wood robotEnd-tied drive pods and room for two odometry wheels.CAD only
  7. EN-65Nov 2 · Wood robotSome nuts on the pod bridges couldn't be reached with a tool: an access plan.Plan / study
  8. EN-80Nov 5 · Wood robotThe rear wheel touched a pod bolt, so we used flush printed pod-end ties.CAD only
  9. EN-81Nov 5 · Wood robotNo wood pod end plates; the power switch is recessed so it can't be bumped off.CAD only
  10. EN-83Nov 6 · Wood robotLong tie bolts replaced with short screws and lock nuts held in printed pockets.CAD only
  11. EN-96Nov 13 · CR1The pod top bridges were too big; a small round tie replaced them (59 to 9.8 cm³).CAD only
  12. EN-107Nov 17 · CR1 v6v6 step 5: full-length side plates cut in one piece on the Glowforge; closed pod ends.Files ready
  13. EN-108Nov 17 · CR1 v6v6 full robot: only 0.35 mm of width to spare, so the pods moved 5 mm in for 0.25 in per side.CAD only

Back to the top

27 entries

Intake, lane + transfer

How a ball gets from the floor into the robot, waits in the lane, and moves up to the shooter.

  1. EN-02Sep 24 · Wood robotWe used the REV through-bore bearings we already had for the intake rollers.Built + tested
  2. EN-04Sep 26 · Wood robotWe laser-cut the ramp back wall instead of printing one long part.Built + tested
  3. EN-09Oct 4 · Wood robotThe sorter guide rail kept breaking, so we made it much stronger.Built, testing
  4. EN-10Oct 4 · Wood robotRoller end caps had holes too small for our tubing.Built, testing
  5. EN-20Oct 14 · Wood robotThe intake rollers rubbed (72.5 mm rollers only 72 mm apart); we also checked every screw.CAD only
  6. EN-27Oct 18 · Wood robotIdea: sort the two balls by size with a slot in the wall.Plan / study
  7. EN-28Oct 18 · Wood robotA separate 5-inch curved ramp bench rig to try the idea.CAD only
  8. EN-29Oct 18 · Wood robotA sorting wall with a 78 mm slot and a second roller.CAD only
  9. EN-30Oct 18 · Wood robotBrackets to hold the intake bench rig together.Files ready
  10. EN-34Oct 19 · Wood robotA back wall and chute from the intake to the pollen shooter.CAD only
  11. EN-35Oct 19 · Wood robotOur rule: the roller touches every ball first. We also lowered the sorting wall.CAD only
  12. EN-36Oct 20 · Wood robotBench test: Pollen went into the slot 5 out of 5 times, Nectar got past it 6 out of 6.Built + tested
  13. EN-37Oct 20 · Wood robotIdea: a wedge turns balls sideways and a bar sorts them.CAD only
  14. EN-38Oct 22 · Wood robotThe bench intake on the drivetrain chassis, with a 345 mm wide roller.Files ready
  15. EN-52Nov 1 · Wood robotA raised ramp, a one-piece nectar guide and a joined front panel.CAD only
  16. EN-53Nov 1 · Wood robotShared roller supports, with the intake chain moved to the outside.CAD only
  17. EN-66Nov 2 · Wood robotA front guard and goBILDA tubing for the intake rollers.Plan / study
  18. EN-78Nov 4 · Wood robotAn intake motor and chain between the rollers; roller 1 made shorter.CAD only
  19. EN-79Nov 5 · Wood robotCleanup: leftover holes filled, transfer guides moved onto the intake panels.CAD only
  20. EN-85Nov 10 · Wood robotStronger reprints of the ramp parts, and steeper wedge halves.CAD only
  21. EN-86Nov 10 · Wood robotTwo ramp mounts broke off at thin spots, so we braced them and opened room for the nuts.CAD only
  22. EN-94Nov 13 · CR1One front rig made from real CR1 parts: intake, lane and transfer.Files ready
  23. EN-97Nov 13 · CR1The intake chain was 0.5 mm from its plate; a bigger plate gives 3.5 mm on each side.CAD only
  24. EN-98Nov 13 · CR1Rear lane floor removed; round printed ties hold the lane plates.CAD only
  25. EN-105Nov 16 · CR1 v6v6 step 3: transfer chain with one idler, both motors straight, a lane floor tray.Files ready
  26. EN-112Nov 19 · v6 METALThe transfer lane fully 3D printed in two pieces (7 parts to 2).Files ready
  27. EN-113Nov 19 · v6 METALAbout 200 mm of the lane had nothing pushing the ball, so we added 3 small lane wheels.CAD only

Back to the top

35 entries

Shooter, turret + head

Launching Pollen into the hive: the October hood shooters, then the CR1 topspin head on a turret with a camera.

  1. EN-08Oct 3 · Wood robotShooter side panels went from slow 3D prints to laser-cut plywood.Built, testing
  2. EN-12Oct 4 · Wood robotWe watched the pollen shooter frame by frame: the wheel wasn't squeezing the ball.Built, testing
  3. EN-14Oct 7 · Wood robotNectar hood: adjustable angle, 11% squeeze and a chain tensioner.CAD only
  4. EN-15Oct 8 · Wood robotFeeder height adjustment and a check that the shooter shaft is strong enough.CAD only
  5. EN-16Oct 8 · Wood robotA comb floor, so there is no gap before the wheel at any hood angle.CAD only
  6. EN-17Oct 9 · Wood robotThe chain tensioner was too thin, so we made it one thick 13.6 mm piece.Files ready
  7. EN-18Oct 14 · Wood robotWe moved the hood drive to the top to make the robot shorter.CAD only
  8. EN-21Oct 14 · Wood robotThe nectar ramp was 0.3 mm from the pollen flywheel; we raised it 20 mm, plus 7 more fixes.CAD only
  9. EN-23Oct 15 · Wood robotWe got every pollen shooter part ready to print on our Bambu A1.Files ready
  10. EN-24Oct 15 · Wood robotFirst try at fitting the nectar shooter in the robot: the hood stuck out 7.65 mm.CAD only
  11. EN-26Oct 16 · Wood robotThe tall hood failed while printing, so we split it in two with pegs.Files ready
  12. EN-31Oct 18 · Wood robotA three-piece hood that turns around the flywheel shaft.CAD only
  13. EN-32Oct 19 · Wood robotWe checked the old nectar drawing and planned a bench build.Plan / study
  14. EN-33Oct 19 · Wood robotA fixed feed ramp plus one geared hood moved by a servo.CAD only
  15. EN-39Oct 23 · Wood robotStronger pollen shooter v4: side walls and motor bracket in one print. Built and bench tested.Built, testing
  16. EN-41Oct 26 · Wood robotNectar shooter v1, copied from the pollen v4 that worked.CAD only
  17. EN-44Oct 27 · Wood robotWhere the two shooters go on the robot: pollen low, nectar high.CAD only
  18. EN-45Oct 29 · Wood robotA deck mount and a powered feeder for the pollen shooter.CAD only
  19. EN-47Oct 31 · Wood robotA feeder wheel idea for the hand-off into the shooter. Rejected: its shaft crossed the ball's path.Not chosen
  20. EN-48Oct 31 · Wood robotA replacement pollen ramp that keeps the same mounting holes.Files ready
  21. EN-50Nov 1 · Wood robotWe moved the shared deck but kept the powered feeder.CAD only
  22. EN-57Nov 1 · Wood robotWe had no good way yet to drive Nectar into its shooter, so it stayed an open question.Plan / study
  23. EN-60Nov 2 · Wood robotThe hood jerked during shots, so we made it stiffer and supported the servo drive.CAD only
  24. EN-64Nov 2 · Wood robotA plan for the final hood, bearings and servo drive.Plan / study
  25. EN-69Nov 2 · Wood robotWe compared the hood at three angles and picked the next gear to try.CAD only
  26. EN-73Nov 3 · Wood robotThe shooter deck now sits on side rails; cleaner side plates.CAD only
  27. EN-74Nov 4 · Wood robotShooter B with a 26-tooth hood gear. Class footage: 3 of 3 shots we could follow bounced out of the hive.CAD only
  28. EN-90Nov 11 · CR1Balls bounced out of the hive because of backspin. New idea: a topspin shooter with the wheel on top. This started CR1.CAD only
  29. EN-91Nov 13 · CR1A bench rig to test the CR1 topspin head before building the robot.Files ready
  30. EN-93Nov 13 · CR1A turret rig: can two servos aim the shooter and hold it still?Files ready
  31. EN-101Nov 14 · CR1No lazy susan in the store, so the turret rig uses the team's AndyMark turret.Files ready
  32. EN-102Nov 16 · CR1The topspin head shot much more consistently on the rig, so we made it one printed piece with the motor tucked under the wheel (9 parts to 1).Files ready
  33. EN-103Nov 16 · CR1A gate holds the ball before the flywheel, and a camera cradle helps aim.Files ready
  34. EN-104Nov 16 · CR1 v6v6 step 2: both turret servo hangers mirrored, one bracket shape for 7 of 8 spots.Files ready
  35. EN-114Nov 20 · v6 METALCamera moved to the top of the shooter head; the back of the head closed around the motor.Files ready

Back to the top

9 entries

Flower wedge

A wedge that slides under a Pollen in the flower so it rolls out to our intake.

  1. EN-58Nov 1 · Wood robotRoom for two outward-facing front servos to move a flower wedge.CAD only
  2. EN-63Nov 2 · Wood robotWe studied video of a wedge lifting Pollen out of the flower.Plan / study
  3. EN-67Nov 2 · Wood robotFirst full CAD revision. One wedge parking spot was rejected because it blocked every shot.CAD only
  4. EN-72Nov 3 · Wood robotThe long wedge linkage reached 703 mm when deployed, so we drew one full-width wedge on two short arms.CAD only
  5. EN-84Nov 10 · Wood robotHow to hold the wedge arms on plain REV hex shafts.Plan / study
  6. EN-92Nov 13 · CR1A test slice: will the steep wedge get under a Pollen in the flower?Files ready
  7. EN-100Nov 14 · CR1A hand bench rig with 100 mm of the real wedge and stops at 3, 4, 5 and 6 degrees.Files ready
  8. EN-109Nov 18 · CR1 v6Wedge arms inside the pods. Modelled, then not chosen: the arms stay outside.Not chosen
  9. EN-115Nov 20 · v6 METALA low-profile wedge so the ball rolls out under the flower's collar: 3 test slices to print.Files ready

Back to the top

7 entries

Electronics + code

Hubs, battery, wiring, sensors and the code that controls the shooter and knows where the robot is.

  1. EN-11Oct 4 · Wood robotWires were hard to reach: an open back plate and a sliding hub drawer.Built, testing
  2. EN-43Oct 26 · Wood robotShooter speed control (PIDF) with live graphs on FTC Dashboard.Code ready
  3. EN-54Nov 1 · Wood robotA carrier for the hubs and a tray and strap for the battery.CAD only
  4. EN-55Nov 1 · Wood robotWe checked room for the hubs, battery, wires and tools.CAD only
  5. EN-82Nov 6 · Wood robotPoster check: we marked which numbers are measured and which are only CAD.Plan / study
  6. EN-99Nov 14 · CR1The Pinpoint odometry sensor now lies flat on a printed shelf, the way goBILDA says.Files ready
  7. EN-110Nov 19 · CR1 v6The supplier found a 0.10 mm sliver at the front cover's switch opening; we fixed the file.Files ready

Back to the top

23 entries

Frame + build process

How we make the robot ourselves: laser-cut plates, 3D prints, bolts, CAD checks and big layout decisions.

  1. EN-01Sep 24 · Wood robotOur plates were too big for the laser, so we split them with seams that step around bolt holes.Built + tested
  2. EN-03Sep 25 · Wood robotOne bolt size: every wood joint uses #8-32 bolts with lock nuts.Built + tested
  3. EN-05Sep 27 · Wood robotA loose strip at a plate seam: three clamp designs, the third one worked.Built + tested
  4. EN-13Oct 5 · Wood robotWe added all 287 bolt heads and nuts to the CAD so the clash check catches them.CAD only
  5. EN-19Oct 14 · Wood robotThe side wall and the shooter wall cut as one board.CAD only
  6. EN-42Oct 26 · Wood robotA printed sleeve so a small bearing fits a 12 mm hole.Files ready
  7. EN-46Oct 31 · Wood robotLayout study: a pinch at the pollen entry and parts too close to the floor.Plan / study
  8. EN-49Nov 1 · Wood robotShared supports to make room for both shooters.CAD only
  9. EN-51Nov 1 · Wood robotA shared rear frame, and a check of how the intake really packs in.CAD only
  10. EN-56Nov 1 · Wood robotA flat front arch for laser cutting, plus fit pieces for the electronics.Files ready
  11. EN-59Nov 1 · Wood robotBig decision: a Pollen-only robot for the qualifier, with stronger end-tied drive pods.Plan / study
  12. EN-62Nov 2 · Wood robotWe joined the pollen robot and the new drivetrain into one model.CAD only
  13. EN-68Nov 2 · Wood robotWe combined the plywood side plates and placed the electronics inside.CAD only
  14. EN-70Nov 3 · Wood robotA library of supplier CAD files, so real part sizes are in our model.CAD only
  15. EN-71Nov 3 · Wood robotWe swapped stand-in parts for exact supplier hardware; all four drive chains are 34 links.CAD only
  16. EN-75Nov 4 · Wood robotBattery, robot number signs and side plates revised (master v5).CAD only
  17. EN-76Nov 4 · Wood robotFewer brackets, no countersinks in wood, wedge servo flipped.CAD only
  18. EN-77Nov 4 · Wood robotPrinted corner brackets instead of nuts hidden in plate edges; a main power switch.CAD only
  19. EN-88Nov 11 · Wood robotWe checked our CAD clash list again in a second program (FreeCAD).CAD only
  20. EN-89Nov 11 · Wood robotRounder outside edges on printed parts, without moving any mounting faces.CAD only
  21. EN-95Nov 13 · CR1Inner side plates redrawn with only the holes we use and clean triangle pockets.CAD only
  22. EN-106Nov 16 · CR1 v6v6 step 4: each robot sign went from 16 parts to one printed panel.Files ready
  23. EN-111Nov 19 · v6 METALA $500 sponsor credit: the 7 main plates in 1/8 in aluminum, without moving any part.Files ready

Back to the top